Feedback

Stagetab grows with its users: the bugs you report and the tools you ask for help decide what comes next.

The tool, version and browser are sent along so the bug can be reproduced. Your email only if you enter it.

Most requested tools

  1. Loading …

Click ▲ to vote. New requests appear after a short review.

← All tools

Audio Engineering Essentials

The basics you keep needing at FOH, during system setup and in planning: levels and decibels, sound and frequency, microphones, cabling, digital audio and exposure limits. With small converters to try things out right away.

Decibels & levels

The decibel is not an absolute value but a logarithmic ratio to a reference. Only the suffix (dBu, dBV, dBFS, dB SPL) tells you what the number refers to. Without a suffix, “dB” just describes a difference, such as “3 dB louder”.

For quantities such as voltage and sound pressure the formula is 20 × log(a/b), for power 10 × log(a/b). That's why double the voltage means +6 dB, but double the power only +3 dB.

UnitReferenceTypical use
dBu0,775 VStudio and pro line level (+4 dBu = 1.23 V)
dBV1 VConsumer line level (−10 dBV = 0.32 V)
dBFSdigital full scaleConsoles, interfaces, DAWs; 0 dBFS is the maximum
dB SPL20 µPa sound pressureLoudness in the room, threshold of hearing at 0 dB SPL
dB(A) / dB(C)dB SPL with frequency weightingA: matches hearing for averages, C: for peaks and bass
+6 dBdouble the voltage or sound pressure
+3 dBdouble the power, two equally loud uncorrelated sources
+10 dBis perceived as roughly twice as loud
1 dBjust noticeable difference in a direct comparison

Converter voltage ↔ level

Adding levels

Sound & frequency

Sound travels through air at 20 °C at about 343 m/s, roughly 0.6 m/s faster per degree Celsius. The wavelength follows from λ = c / f. It explains many effects in practice: low frequencies with wavelengths of several metres bend around obstacles and are hard to control, while high frequencies are already shadowed by people and scenery.

FrequencyWavelengthWhat it means in practice
20 Hz17,2 mlower limit of hearing, felt more than heard
50 Hz6,9 mkick drum punch, room modes in small halls
100 Hz3,4 mtypical sub/top crossover region
1 kHz34 cmreference tone for level matching
4 kHz8,6 cmregion of highest ear sensitivity
10 kHz3,4 cmhighly directional, easily shadowed

Calculate wavelength

An octave is a doubling of frequency. Human hearing covers about ten octaves from roughly 20 Hz to 20 kHz, with the upper limit dropping noticeably with age. That's why analysers often work in third-octave bands, i.e. three bands per octave.

Frequency ranges for mixing

The boundaries are fluid, but this breakdown has proven useful as an EQ guide:

RangeFrequencySounds likeTypical moves
Sub bass20–60 HzPunch, bodyHigh-pass everything that doesn't belong down there
Bass60–250 HzFoundation, warmthSeparate kick and bass, cut boominess
Low mids250–500 HzFullness or “cardboard”most common area to cut mud
Mids500 Hz–2 kHzCore, cut-through, “nasal”Shape speech and guitars
Presence2–5 kHzIntelligibility, closenessboost carefully, gets harsh quickly
Air5–20 kHzAir, sheen, sibilanceDe-essing at 5–8 kHz, shelf for air

The fundamental of the speaking voice is usually around 100–150 Hz for men and 200–250 Hz for women. For intelligibility, though, the consonants between 2 and 4 kHz matter most. A high-pass at 80–120 Hz on speech mics costs almost nothing and reduces footfall noise and plosives.

Loudness & limits

dB SPLExample
0Threshold of hearing at 1 kHz
30quiet room, whispering
60normal conversation at 1 m
85heavy traffic; hearing damage from here with prolonged exposure
95–100rock concert at FOH, nightclub
120right in front of the PA, approaching the pain threshold
130+pain threshold, damage even from short exposure

Audience (German standard DIN 15905-5:2022-07): For events with electro-acoustic amplification the guide value is a rating level of 99 dB(A), averaged over 30-minute periods; the peak level must not exceed 135 dB(C). Measurements use a meter of at least accuracy class 2.

Staff (German Noise and Vibration Occupational Safety Ordinance): From a daily noise exposure level of 80 dB(A) hearing protection must be provided, from 85 dB(A) it must be worn. For peak levels the action values are 135 and 137 dB(C). These values match the EU noise directive.

Every 3 dB increase halves the permissible exposure time for the same hearing dose. Eight hours at 85 dB(A) equals one hour at 94 dB(A). The exact obligations are set out in the applicable standards and regulations; if in doubt, their current wording applies.

Microphones

Dynamic microphones use a moving coil, need no power, handle high levels and are rugged. Ideal for vocals on stage, snare and guitar amps. Condenser microphones need phantom power, resolve more detail and respond faster to transients. Good for overheads, acoustic instruments and speech in quiet surroundings.

Polar patternLeast sensitive directionUse
Omninone, picks up all aroundRoom, lavaliers, measurement mics
Cardioidrear (180°)Standard for vocals, monitor directly behind
Supercardioidapprox. 125° rear sidesloud stages, monitors angled behind
Hypercardioidapprox. 110°even tighter rejection, small rear lobe
Figure-8sides (90°)Two-person interviews, M/S stereo, ribbons

Proximity effect: Directional microphones boost low frequencies the closer the source is. It makes voices fuller, but also explains the boominess of singers who practically swallow the mic.

Phantom power P48: 48 V DC, carried on signal pins 2 and 3 against ground. It doesn't harm dynamic mics on balanced lines. Take care with ribbon mics on faulty cabling, unbalanced devices and when plugging with phantom on.

3:1 rule: When two mics pick up the same source, the second should be at least three times as far away as the first is from the source. This keeps comb filtering from time differences small.

Cables & connectors

Balanced lines carry the signal twice with opposite polarity. The input takes the difference, so interference arriving equally on both conductors cancels out. That's why 50 m of mic cable works fine, while an unbalanced jack cable starts humming after a few metres.

ConnectorWiring
XLR (3-pin)Pin 1 ground/shield, pin 2 hot (+), pin 3 cold (−)
Jack TRS (stereo)Tip hot (+), ring cold (−), sleeve ground – or stereo left/right
Jack TS (mono)Tip signal, sleeve ground – always unbalanced
Speakon NL41+ / 1− for the first way, 2+ / 2− for the second (e.g. bi-amp)
Signal typeTypical levelNote
Microphoneapprox. −60 to −20 dBuneeds a preamp (gain)
Instrument (guitar, bass)approx. −20 dBu, high impedanceDI box for long runs and balancing
Line consumer−10 dBVLaptops, players, hi-fi
Line pro+4 dBuConsoles, controllers, amp inputs
Speakerup to well over 100 Vnever into line or mic inputs

Hum usually means a ground loop: two devices are connected twice, via protective earth and audio ground. The fix is a DI box or an isolation transformer with ground lift, never taping over or disconnecting the protective earth.

Digital audio

The Sample rate sets the highest frequency that can be carried: just under half the sample rate (Nyquist). 48 kHz covers the whole audible range and is standard in live and video. 96 kHz mainly reduces latency and filter effects in processing.

The bit depth determines the theoretical dynamic range, about 6 dB per bit: 16 bits give around 96 dB, 24 bits around 144 dB. That's why with 24 bits it's no problem to leave some headroom instead of running just below 0 dBFS.

Latency & dynamic range

With digital consoles and networks such as Dante, latency adds up with every conversion and network hop. For in-ear monitoring the whole chain should stay well below 10 ms, otherwise your own voice sounds smeared.

Loudspeakers & room

Inverse square law: A point source loses 6 dB per doubling of distance. In its near field a line array loses only about 3 dB per doubling and therefore throws further back. You'll find the calculator here in Stagetab.

Polarity and phase: Polarity simply swaps plus and minus across all frequencies. Phase is a time shift whose effect depends on frequency. So a polarity switch on the console doesn't fix time differences between sub and top; that takes delay.

Comb filtering: When two identical signals combine with a small time offset, some frequencies cancel and others add up. It happens with two mics on one source or two speakers playing the same programme. Delay, distance or deliberately separate coverage areas help.

Haas effect: If a second sound arrives within about 5 to 30 ms of the first, the ear localises the source at the first signal, even if the second is louder. That's why a delay line is fed a few milliseconds later than the pure propagation time. See the Delay Calculator.

Reverberation: The reverberation time RT60 is the time it takes for the level to fall by 60 dB after the source stops. According to Sabine, roughly RT60 = 0,161 × V / A (room volume in m³, equivalent absorption area in m²). For speech, under 1 second is comfortable; churches and empty halls are often 2 to 4 seconds. An audience absorbs a lot, so a full hall sounds much drier than at soundcheck.

Formulas at a glance

QuantityFormula
Level from voltage / sound pressureL = 20 × log(U / U₀)
Level from powerL = 10 × log(P / P₀)
dBu → voltsU = 0,775 V × 10^(dBu / 20)
Speed of soundc ≈ 331,3 + 0,606 × T (m/s, T in °C)
Wavelengthλ = c / f
Propagation timet = d / c
Level drop point sourceΔL = 20 × log(d₂ / d₁)
n equal, uncorrelated sourcesL + 10 × log(n)
Digital dynamic range≈ 6,02 × Bit + 1,76 dB
Latencyt = Samples / Abtastrate
Reverberation time (Sabine)RT60 = 0,161 × V / A
Ohm's law / powerU = R × I, P = U² / R

Further reading

If you want to dig deeper, sengpielaudio.com by Eberhard Sengpiel offers an extensive collection of articles, tables and online calculators on audio engineering and acoustics (mostly in German, many pages also in English).

Subwoofer Array Simulator

How do broadside, cardioid, end-fire or a delay arc behave in a room? The simulator shows the level distribution of several subwoofers in plan and 3D view, with delay, gain and polarity per sub.

Open the subwoofer simulator

About Stagetab

All calculations run locally in your browser. Nothing you enter is transmitted; run sheets and soundboard labels are stored on your device only.

The calculators provide guide values for planning and setup. Manufacturer data, on-site measurements and safety regulations always take precedence.

Need technical production for your event?

ES-Sound plans and runs sound, lighting and video for corporate events, concerts and celebrations.

Request a quote

Licences & trademarks

Terms of use

  1. Stagetab may be used free of charge for planning and running your own events, including commercially.
  2. Redistribution, sale, modification, reverse engineering and copying parts of the software into other products are not permitted. Stagetab is provided exclusively via es-sound.de.
  3. All calculations (e.g. loads, power, levels) are guide values and do not replace checks by competent personnel. The user or the responsible specialist on site is responsible for set-up, safety and sign-off.
  4. Stagetab is provided without warranty. ES-Sound is only liable for intent and gross negligence, as far as permitted by law.
  5. Project data stays in your browser or on your computer. Stagetab does not send any project data to ES-Sound.

Software, data and fonts

The ES-Sound Stagetab uses the following software, data and fonts. The full licence texts are included with the files.

ComponentRights holderLicence
three.js (3D rendering)three.js authorsMIT
systray (hardware bridge tray icon)Fyne.io project, GetlanternApache 2.0
godbus (hardware bridge on Linux)Georg Reinke and contributorsBSD 2-Clause
Go x/sys (hardware bridge on Windows)The Go AuthorsBSD 3-Clause
MapLibre GL JS (map in the site plan)MapLibre contributorsBSD 3-Clause
Map data in the site plan (only when a map is selected)OpenFreeMap, OpenMapTiles, OpenStreetMap contributorsODbL
PDF.js (PDF as floor plan)Mozilla FoundationApache 2.0
ONNX Runtime WebMicrosoft CorporationMIT
AI model “Beat This!” (beat tracking)Institute of Computational Perception, JKU Linz; Johannes GorsetMIT
Essentia models for mood detection (AI module only)Music Technology Group, Universitat Pompeu Fabra, BarcelonaCC BY-NC-SA 4.0
fft.jsFedor IndutnyMIT
Transformers.js (live translation, in the AI module)Hugging Face, Inc.Apache 2.0
Silero VAD 6.2.3 (voice activity detection, in the AI module)Silero TeamMIT
AI model Whisper large-v3-turbo (only after download in live translation)OpenAI; ONNX version onnx-communityMIT
AI models Whisper small and base (only after download)OpenAI; ONNX version onnx-communityApache 2.0
AI models Opus-MT English → German (only after download)Language Technology Research Group, University of Helsinki (Helsinki-NLP); ONNX version XenovaCC BY 4.0
AI models Opus-MT German → English/French/Spanish, English → French/Spanish/Italian/Dutch/Russian/Ukrainian (only after download)Language Technology Research Group, University of Helsinki (Helsinki-NLP); ONNX version XenovaApache 2.0
AI language model Qwen3.5-2B (“quality” translation, only after download)Qwen team (Alibaba Cloud); ONNX version onnx-communityApache 2.0
Speech output of live translation: eSpeak NG (separate module in the AI folder, with source code)eSpeak NG contributorsGPL-3.0-or-later
AI voices Piper (speech output, only after download): Thorsten (de), Davefx (es), Pim (nl), ukrainian_tts (uk), Darkman (pl)Thorsten Müller; Open Home Foundation (rhasspy/piper-voices)CC0
AI voice Piper LJSpeech (en, only after download)Keith Ito (LJ Speech), Bryce Beattiepublic domain
AI voices Piper Siwis (fr), Paola (it), Dmitri (ru) (only after download)SIWIS (University of Edinburgh); Open Home Foundation; base model hifi_tts_92 from the Hi-Fi Multi-Speaker English TTS Dataset (NVIDIA Corporation)CC BY 4.0 (Siwis, base model), CC0 (Paola, Dmitri)
Open Fixture Library (fixture data)Florian & Felix Edelmann and contributorsMIT
GDTF files from GDTF Share (Powered by GDTF)Manufacturers or users who uploaded the file; GDTF Share by MA Lighting, Robe and VectorworksTerms of use of gdtf-share.com; GDTF is DIN SPEC 15800
Fonts Barlow Condensed, IBM Plex Sans, JetBrains MonoJeremy Tribby; IBM Corp.; JetBrains s.r.o.SIL Open Font License 1.1
Windows app: Electron and ChromiumOpenJS Foundation, The Chromium AuthorsMIT and others, see program folder

GDTF and MVR are open formats according to DIN SPEC 15800. The lighting plot symbols follow the USITT recommendations (RP-2) and are our own drawings.

Trademarks

Product and company names mentioned, e.g. of fixture, truss and console manufacturers, are trademarks of their respective owners. They are used only to identify devices, formats and compatibility. The Stagetab is not affiliated with or endorsed by these manufacturers. Manufacturers' fixture files remain their property.

This page gathers the knowledge you keep needing at FOH, during system setup and in planning. That includes levels and decibels, sound and frequency, microphones, cabling, digital audio and exposure limits. Small converters also let you try things out right away. Everything is free and needs no sign-up.

What knowledge you will find here

The basics are explained briefly and with practice in mind. For example, a table shows what dBu, dBV, dBFS and dB SPL refer to. Then comes an overview of frequency ranges for mixing. It tells you where punch, mud or sibilance sit.

The microphone section covers dynamic and condenser mics. It also deals with polar patterns, phantom power and the 3:1 rule. In addition, the page explains balanced lines, connector wiring and typical signal levels.

Calculate instead of guessing

Many topics come with a small calculator. That way you can convert voltage to dBu and dBV. You can add up the levels of several sources or find the wavelength at a given temperature. You can also work out latency and dynamic range directly.

At the end there is a set of formulas at a glance. It runs from level from voltage to reverb time according to Sabine. This is handy when you need to look something up quickly on site.

Audio engineering knowledge in the ES-Sound Stagetab with tables and calculators

Knowledge on loudness and rooms

A separate section deals with loudness and limits. There you will find the guideline values of DIN 15905-5 for the audience. It also lists the action values of the German noise and vibration regulations for staff. If in doubt, however, the current wording of the standard always applies.

After that, the page turns to loudspeakers and rooms. Topics include the inverse square law, polarity and phase, comb filtering, the Haas effect and reverb. A subwoofer simulator also shows how arrays behave in the room.

Further reading and next steps

The decibel article on Wikipedia is also a good introduction to levels. For practical work there are matching tools. With the delay calculator you can time delay lines. The SPL distance calculator shows how level drops over distance. You can check the frequency response with the RTA analyser. You will find every tool in the Stagetab.

Nach oben scrollen